Levelord´s Super Snake @ WinsenRacers

[Levelord]

Construction phase 23 - The middle chassis

Now we get the middle chassis delivered, attach it to the as shownrear chassis and screw both with four MD06 screws.
It is advisable to put a drop of oil on the screws.

[Levelord]

Construction phase 24 - The front floor pan

Take the floor pan and insert it into the middle chassis as shown.
Fasten both with a type MP03 screw at the front. Then insert the four MD02 screws from the side.
For the rest of the fastening we use four MD06 screws.

[Levelord]

Construction phase 25 - the cardan shaft

We now put both halves of the cardan shaft together and screw both together
three MP02 screws.
Then we insert the cardan shaft into the rear differential and insert the holding points into the chassis.
Screw both with two MP01 screws.

[Levelord]

Construction phase 26 - transmission and cross member

Now insert the gearbox on the middle chassis and fasten it with two
MP01 screws.
We now also put the cross member on top of the gearbox and fasten it with it
two screws type MP01.

[Levelord]

Construction phase 27 - The front chassis

Now guide the front chassis to the middle chassis and screw both with screws
MD06.

[Levelord]

Construction phase 28 - fender splash guard

Now we mount a splash guard on the front chassis at the fender.
Insert these as you can see and screw both with two screws each
MD06.

[Levelord]

Construction phase 29 - The handlebars

Align the handlebars as you can see in the pictures and screw all three together
with two screws MD02.
Make sure that the handlebars remain flexible.

[Levelord]

Construction phase 30 - wheel suspension and steering

Now mount both brackets of the wheel suspension on the chassis and fasten them with it
one MD06 screw each.
Then we put the steering gear on the chassis and screw it to an MP01
Screw.
Now we take the steering linkage again and put the steering arm on. Attach this
with an MD02 screw. Make sure that the steering arm remains movable.

[Levelord]

Construction phase 31 - stabilizers and wheel suspension

 

Attaches the stabilizers to the front chassis from below. Fix it from above with two screws
MP03.
Use a pin on each of the suspension. So the wheel suspension remains mobile.

Finally, we insert the handlebars as shown. Secure this with some paper tape
provisionally.

[Levelord]

Construction phase 32 - The upper wishbone

Take a bracket and a wishbone and put them together, push a step through
the holes. We assemble the other wishbone in the same way.
Then mount the wishbones on the chassis with two MD06 screws each.

[Levelord]

Stage 32 - The floor and the gear lever

Put the shift lever on the floor from above and screw both with an MP01 screw.

[Levelord]

Construction phase 34 - The pedals and microswitches

first we put the two side parts on the floor and screw them together with two
MP01 and an MP03 screw.
Then we put the two microswitches in the bracket and mount them on the floor.
We'll use an MP01 screw for this.
Now we insert the pedals from above and fasten them with two MP01 screws.
The accelerator pedal and brake pedal should now operate both microswitches.

[Levelord]

Construction phase 35 - dashboard and cover of the fuse box

Take the cover of the fuse box and place it on the dashboard.
Screw this from behind with an MP03 screw.

[Levelord]

Construction phase 36 - The dashboard (2)

Now get the dashboard again in front of us and insert the stickers.
Then you take the first chrome strip and insert the speedometer glasses.
Now leads the first chrome strip onto the dashboard. Then you put the
second chrome strip.
Then screw the strips from behind with three screws MP01.
Then stick the Shelby logo on the base and insert it into the dashboard.
You screw this from behind with two MP05 screws.

[Levelord]

Construction phase 37 - The dashboard (3)

First insert the radio into the dashboard and secure it with two MP01 screws.
Then you take the watch and insert the dial. Then you insert the pane of glass.
Now mount the front part of the clock and screw everything together with an MP05 screw.
The clock is then inserted into the dashboard and secured with an MP05 screw.
Now insert the back part of the glove compartment and screw it down with three MP01 screws.
From the inside we are now assembling the flap of the glove compartment.

Finally we mount the dashboard on the floor with two MP03 screws.

[Levelord]

Construction phase 38 - The rear floor and straps

First, we insert both belt buckles into the back floor.
then we put the rear floor on the front and screw both
with four MP01 screws.
Then guide the straps through the floor as shown and fix them from below.

[Levelord]

Construction phase 39 - Interior details

It continues with the interior of our SuperSnake.
Take the first front doormat and insert it as shown. Presses this
firmly. The second front doormat and both of them follow in the same way
rear.
Then we put the seats on the floor and screw them with two each
MP01 screws from below.
We insert the belt buckles as shown.
Now assemble the fire extinguisher and then put it between the two seats.

[Levelord]

Construction phase 40 - The rear seat bracket

Leads the bracket to the floor from below and screw both with 4 screws MP01.

 

[Levelord]

What is wrong here? Why are the images no longer displayed?

[admin]

46 minutes ago, Levelord said:

What is wrong here? Why are the images no longer displayed?

Hi, the forum got upgraded over the week-end and seems to have had a couple of glitches. I have refreshed your account - can you try again see if it uploads?

thanks!

 

[Levelord]

Construction phase 39 - Interior details

It continues with the interior of our SuperSnake.
Take the first front doormat and insert it as shown. Presses this
firmly. The second front doormat and both of them follow in the same way
rear.
Then we put the seats on the floor and screw them with two each
MP01 screws from below.
We insert the belt buckles as shown.
Now assemble the fire extinguisher and then put it between the two seats.

[Levelord]

1 hour ago, admin said:

Hi, the forum got upgraded over the week-end and seems to have had a couple of glitches. I have refreshed your account - can you try again see if it uploads?

thanks!

 

Hi, it doesn't work yet. The forum does not recognize the BB codes. All of my images are hosted externally. The only strange thing is that the old posts from me work, only the new ones don't.

[Mario´s Schiffsmodellbau]

Ist bei mir auch so,

 

habe jedes Bild einzeln eingefügt.

Grafikadresse kopieren und dann hier eingefügt.

 

Gruß Mario

[admin]

18 hours ago, Levelord said:

What is wrong here? Why are the images no longer displayed?

Hi, the forum got upgraded over the week-end and seems to have had a couple of glitches. I have refreshed your account - can you try again see if it uploads?

thanks!

16 hours ago, Levelord said:

Hi, it doesn't work yet. The forum does not recognize the BB codes. All of my images are hosted externally. The only strange thing is that the old posts from me work, only the new ones don't.

 

I just tried one of your links in a brand new post, and it automatically embedded the photo correctly. Seems though the earlier posts haven't pulled the pics in. So I did a fix by cutting your image link and then pressing the "other media" button in the bottom right, and selecting "insert image from url", as in this screen grab. 

 

 

then pasting in your link (minus the [img] and [/img] and that fixed it:

 

So now all your old pictures are showing OK.

Hopefully going forward the system will automatically put the images in for you on a new post (as they did for me), but as a fall-back you can use the 'other media' button.

 

[Levelord]

Only Test!

 

[img]https://up.picr.de/39608686mb.jpeg[/img]